Home > Hard Drive > Master Slave Hard Drive Setup

Master Slave Hard Drive Setup

Contents

If you have this backwards the drive will normally either be silent or fail to power up. About Press Copyright Creators Advertise Developers +YouTube Terms Privacy Policy & Safety Send feedback Test new features Loading... Of the two of them, one is labeled P3 and the other P5. Product Key Does Not Match Current Windows SKU Error Review of FastAgain PC Booster and How to Uninstall it How to Remove MSBLAST.EXE worm How to Remove Content Advisor Password in news

Not likely though, esp if you plugged the new drive into the same controller and it shows up. Please refer to our CNET Forums policies for details. Flag Permalink This was helpful (0) Collapse - Jumpers. . . The only difference between them is the old one is 120 gig and the new one is 130 gig.I want to make the new drive the primary drive and use the http://www.wikihow.com/Configure-Master-and-Slave-in-BIOS-for-Two-Hard-Drive-Disk-in-a-Single-System

Master Slave Hard Drive Setup

Jason Hammack 183,841 views 6:49 How to Set Up an IDE Master/Slave Configuration - Duration: 1:14. On even older mainboards you'll find a 32 GB limit. You'll notice in the picture below the jumpers are circled on the end of the drive and the top of the drive shows the diagram to follow.After changing the jumpers, connect Usually, the BIOS will attempt to boot from each drive in order, which means you can set your DVD drive to first and the hard drive on which Windows is installed

On Intel boards, for example, SATA II ports tend to be black; SATA III ports are blue. ALL RIGHTS RESERVED. Watch carefully for the initial boot screen to display and tap the necessary key to over-ride the boot process. Sata Hard Drive Slave Jumper Setting Simply turn on your PC, press the Del key a few times (or look for a message telling which key to press to enter Setup) and the BIOS should appear.

Download Center| Support| Live Chat| United States| My Account EaseUS STORE Product Family Data Recovery Partition Manager Todo Backup Utilities Top Products Data Recovery Wizard Pro for Win Buy Data Recovery Master Slave Hard Drive Jumper Settings Certainly, retail packaged hard drives will have an install disk for you. The disk with all of the unallocated space is what you're after. If you do it right, the BIOS setup screen appears. 2 If prompted for a password, enter it and press the "Enter" key. 3 Navigate to the "CMOS Setup" and press

After booting the computer I also checked in device manager, my old doesn't show up. How To Install A Second Sata Hard Drive In Windows 7 Watch Queue Queue __count__/__total__ Find out whyClose Computer Upgrades & Repairs : How to Change the Master/Slave Designation on a Hard Drive expertvillage SubscribeSubscribedUnsubscribe3,061,4053M Loading... Troubleshooting No hard drives show up: Do you have two drives on the cable? If not, manually restart it.

  • For example, a modern SSD is likely to support the SATA III standard, also known as SATA 6.0Gb/s.
  • If this is being installed as a secondary storage drive for Windows, then you can go into the built in utility called "Disk Management".
  • If you want to make it the master or the slave, you will have to look around the drive to find where the instructions are.
  • Verify the drive is enabled in system BIOS.
  • Working...
  • With the newer Ultra DMA cables, you can set both drives to Cable Select (CS), connect them and they will work.

Master Slave Hard Drive Jumper Settings

Your motherboard might have some SATA II ports (running at 3Gb/s) and some SATA III ports. http://www.tomshardware.com/forum/277623-32-master-slave-sata-drives Make sure that both IDE channels are enabled. Master Slave Hard Drive Setup Powered by Mediawiki. What Is A Slave Hard Drive Warnings Make sure you and your computer are grounded properly to prevent accidental electrical shock or Mother Board damages caused from electrical surges.

Co-authors: 6 Updated: Views:464,354 Quick Tips Related ArticlesHow to Update Your Computer's BIOSHow to Identify the MotherboardHow to Find and Update DriversHow to Ground Yourself to Avoid Destroying a Computer with http://recupsoft.com/hard-drive/can-i-put-my-hard-drive-in-another-computer.html It is a difference in the way the OS and the manufacturers measure drive size. take a look. Make sure the jumpers are set to Cable Select or CS on both and it [should] work as you had originally expected."I hate to be obtuse, but what and where are How To Slave A Sata Hard Drive

Press the "Enter" key to detect and configure the primary hard disk, making it the Master Drive. 5 Move the cursor to the "Primary Slave" selection and press "Enter" again. greatestunknown 74,604 views 3:00 How to transfer files from a Dead PC [CC] - Duration: 11:35. Note: If you want to recover data from the "OLD" drive, don't do this! http://recupsoft.com/hard-drive/how-to-transfer-files-from-external-hard-drive-to-external-hard-drive.html Assign the drive letter.

A lot of people like to use what is called Cable Select. Difference Between Master And Slave Drive About this wikiHow How helpful is this? Answer this question Flag as...

Save and exit the system setup program.

Install hard drive Before you install the new drive make sure you unplug the power connector from the computer. Anytime you mess with anything inside your computer it is a good idea to unplug it. Make sure the power is plugged in and everything is connected securely. How To Slave A Hard Drive To Recover Data About this wikiHow How helpful is this?

The figure below depicts the jumper settings for the U-Series and Barracuda ATA drive families (most Seagate ATA drives above 20 GBytes). The hard drive doesn't even power up: Check to make sure the IDE cable is connected correctly. Tips Typically a computer can have up to 4 drives. click site Watch QueueQueueWatch QueueQueue Remove allDisconnect The next video is startingstop Loading...

Needle-nose pliers for removing or adding jumpers. When you try to install a really big hard drive into a lot of older systems, you'll find that the BIOS is only capable of seeing 137 GB. take a look. Flag as...

Depending on your computer model it will be either "Delete," or "F2." Press it a few times before your Operating System (Windows, etc.) starts up. Now you should be able to find an open 3.5" slot somewhere. Of all the parts of a computer that I hate to replace, besides swapping out the MB, it's the memory cards.Again, thanks for your time and help,KB Flag Permalink This was Flag as duplicate Thanks!

Need more storage space? Track this discussion and email me when there are updates If you're asking for technical help, please be sure to include all your system info, including operating system, model number, and